Looking for a front drive shaft. I think the 86” and 107” fronts are the same.
Thanks!
Series 1 front drive shaft 1954-1957
Forum rules
By posting in this forum, you agree not to post anything abusive, obscene, vulgar, slanderous, hateful or threatening, Doing so may lead to you being immediately and permanently banned.
By posting in this forum, you agree not to post anything abusive, obscene, vulgar, slanderous, hateful or threatening, Doing so may lead to you being immediately and permanently banned.
-
roverdevin
- Junkyard Master
- Posts: 160
- Joined: Sat Feb 28, 2004 11:02 am
- Location: Squamish, BC
- Contact:
-
bsa_m21
- Spanner Man
- Posts: 812
- Joined: Mon Mar 02, 2015 1:30 pm
- Location: Surrey, BC
Re: Series 1 front drive shaft 1954-1957
Series 1 driveshaft lengths:
80 (1948-50) Front 521mm / 20.512"
80 (1948-50) Rear 386mm / 15.197”
80 (1950-53) Front 554mm / 21.812"
80 (1950-53) Rear 407mm / 16.024”
86, 88 Front: 604mm / 23.812"
86, 88 Rear: 554mm / 21.812"
107, 109 Front: 604mm / 23.812"
107, 109 Rear: 1087mm / 42.812"
Series 2/3 driveshaft length (non-Salisbury):
88 (4 cyl) Front: 604mm / 23.812"
88 (4 cyl) Rear: 554mm / 21.812"
109 (4 cyl) Front: 604mm / 23.812"
109 (4 cyl) Rear: 1463mm / 57.600"
M.
80 (1948-50) Front 521mm / 20.512"
80 (1948-50) Rear 386mm / 15.197”
80 (1950-53) Front 554mm / 21.812"
80 (1950-53) Rear 407mm / 16.024”
86, 88 Front: 604mm / 23.812"
86, 88 Rear: 554mm / 21.812"
107, 109 Front: 604mm / 23.812"
107, 109 Rear: 1087mm / 42.812"
Series 2/3 driveshaft length (non-Salisbury):
88 (4 cyl) Front: 604mm / 23.812"
88 (4 cyl) Rear: 554mm / 21.812"
109 (4 cyl) Front: 604mm / 23.812"
109 (4 cyl) Rear: 1463mm / 57.600"
M.
-
mepham55
- Spanner Man
- Posts: 835
- Joined: Fri Mar 26, 2004 8:38 pm
- Location: Victoria, BC, Canada
Re: Series 1 front drive shaft 1954-1957
I’ve got some spare front props. Looks like what Martin has posted shows the 86” is the same as all other Rover front props.
Matt
Matt
-
roverdevin
- Junkyard Master
- Posts: 160
- Joined: Sat Feb 28, 2004 11:02 am
- Location: Squamish, BC
- Contact:
Re: Series 1 front drive shaft 1954-1957
So looks like and series front after 54 should be fine! Does anyone know if there are differences in them beside length? I’ll take anything serviceable. I will be changing the ujoints.
-
roverdevin
- Junkyard Master
- Posts: 160
- Joined: Sat Feb 28, 2004 11:02 am
- Location: Squamish, BC
- Contact:
Re: Series 1 front drive shaft 1954-1957
Scratch that. I just found one in the back barn. I guess it’s time to do some inventory.